PVS-69 Hardware Kit
The PVS-69 by Vonscherf Arms is the industries first consumer level DIY night vision option. Utilizing a 3d printed housing, the PVS-69 Alpha 1.1 is able to use both standard military Image intensifier units, or for a more affordable route can be fitted with small low light FPV drone cameras for a digital night vision option.
This Hardware kit contains everything you need to assemble the housings (NOT INCLUDED), with circuit boards and hardwarefor use in either digital or analog configurations.
*IMPORTANT* Voltage Regulated Battery Pack is required as there is no linger a buck converter option. Analog should not take more than 3v, digital will be dependent on components used.
Parts kit contains:
1x Push button switch
1x Female DC Jack
4x M3 Nyloc nuts
4x M3x45mm bolts
2x M3 Fender Washer
1x M3 Heatset Insert
1x M3x8mm Bolt
4x Brass Washers
4x Leaf Connectors
1x Regulated Bridge Circuit Board
2x Tube Circuit Boards
*You will still need lenses, (pvs14 eye pieces and objective lenses for analog, or pvs 14 eyepieces and 8mm cs lenses for digital) and either mx10160 Image Intensifier Tubes or Cameras and screens*
3d Print Files are available for purchase at Vonscherf Arms
The PVS-69 by Vonscherf Arms is the industries first consumer level DIY night vision option. Utilizing a 3d printed housing, the PVS-69 Alpha 1.1 is able to use both standard military Image intensifier units, or for a more affordable route can be fitted with small low light FPV drone cameras for a digital night vision option.
This Hardware kit contains everything you need to assemble the housings (NOT INCLUDED), with circuit boards and hardwarefor use in either digital or analog configurations.
*IMPORTANT* Voltage Regulated Battery Pack is required as there is no linger a buck converter option. Analog should not take more than 3v, digital will be dependent on components used.
Parts kit contains:
1x Push button switch
1x Female DC Jack
4x M3 Nyloc nuts
4x M3x45mm bolts
2x M3 Fender Washer
1x M3 Heatset Insert
1x M3x8mm Bolt
4x Brass Washers
4x Leaf Connectors
1x Regulated Bridge Circuit Board
2x Tube Circuit Boards
*You will still need lenses, (pvs14 eye pieces and objective lenses for analog, or pvs 14 eyepieces and 8mm cs lenses for digital) and either mx10160 Image Intensifier Tubes or Cameras and screens*
3d Print Files are available for purchase at Vonscherf Arms
The PVS-69 by Vonscherf Arms is the industries first consumer level DIY night vision option. Utilizing a 3d printed housing, the PVS-69 Alpha 1.1 is able to use both standard military Image intensifier units, or for a more affordable route can be fitted with small low light FPV drone cameras for a digital night vision option.
This Hardware kit contains everything you need to assemble the housings (NOT INCLUDED), with circuit boards and hardwarefor use in either digital or analog configurations.
*IMPORTANT* Voltage Regulated Battery Pack is required as there is no linger a buck converter option. Analog should not take more than 3v, digital will be dependent on components used.
Parts kit contains:
1x Push button switch
1x Female DC Jack
4x M3 Nyloc nuts
4x M3x45mm bolts
2x M3 Fender Washer
1x M3 Heatset Insert
1x M3x8mm Bolt
4x Brass Washers
4x Leaf Connectors
1x Regulated Bridge Circuit Board
2x Tube Circuit Boards
*You will still need lenses, (pvs14 eye pieces and objective lenses for analog, or pvs 14 eyepieces and 8mm cs lenses for digital) and either mx10160 Image Intensifier Tubes or Cameras and screens*
3d Print Files are available for purchase at Vonscherf Arms